You Searched For: I.W. TREMONT CO., INC.

Supplier: I.W. TREMONT CO., INC.

Description: LabExact® Grade A83 nano-scale glass microfiber has the loading capacity of a binderless glass microfiber filter with the tight, regulated pore size of a membrane. This specialty grade has a particle retention of 0.5 µm.

New Product

Supplier: I.W. TREMONT CO., INC.

Description: Nylon syringe filters are recommended for filtration of aqueous or organic/aqueous medium polar liquids and commonly used for general laboratory filtration and filtration of HPLC and GC samples prior to injection. The non-sterile disposable syringe filters with 4 mm diameter are ideal for processing small samples.

New Product

Supplier: I.W. TREMONT CO., INC.

Description: H&V Trupor® PES membranes utilize nanoscale technology in a composite design to achieve precisely regulated porosities with higher loading capacity and faster flow. No adhesives are utilized, which significantly reduces trace extractables.

New Product

Supplier: I.W. TREMONT CO., INC.

Description: Demonstrating medium retention and flow rates, this media is widely used in many general quantitative procedures in both liquid and gas.

New Product

Supplier: I.W. TREMONT CO., INC.

Description: LabExact® disposable non-sterile PES/polyethersulfone hydrophilic filtration media syringe filters have high filtration flow rates and an inherently low affinity for proteins and low extractables ideal for introduction of additives into tissue culture vessel.

New Product

Supplier: I.W. TREMONT CO., INC.

Description: LabExact® Total Suspended Solids (TSS) filters are processed to US EPA Standard Method 2540 C, D and E, washed using reagent grade water, dried, desiccated and weighed to 4 decimal place resolution.

New Product

Supplier: I.W. TREMONT CO., INC.

Description: Very fast flow rates and loose retention characteristics make this grade ideal for initial separation of gelatinous precipitates.

New Product

Supplier: I.W. TREMONT CO., INC.

Description: Virtually identical to CFP1, but twice as thick, resulting in a significantly slower flow rate with a retention of approximately 6 µm.

New Product

Supplier: I.W. TREMONT CO., INC.

Description: LabExact® Grade VSS is a binder-free material manufactured using a proprietary glass chemistry which permits usage in high heat applications beyond typical borosilicate glass blends. Ideally suited for determination of fixed and volatile solids ignited at 550 °C Method 2540E.

New Product

Supplier: I.W. TREMONT CO., INC.

Description: Positioned as an intermediate within the quantitative cellulose family, this grade demonstrates medium retention and flow rates.

New Product

Supplier: I.W. TREMONT CO., INC.

Description: LabExact® disposable non-sterile nylon/polyamide filtration media syringe filters are hydrophilic with a 1 µm glass microfiber prefilter that raises absorption capacity and loading.

New Product

Supplier: I.W. TREMONT CO., INC.

Description: These cellulose filters create a hydrophobic barrier that can replace a separatory funnel to separate organic solvents from aqueous phase.

New Product

Supplier: I.W. TREMONT CO., INC.

Description: LabExact® disposable non-sterile Cellulose Acetate hydrophilic syringe filters have very low binding capacity for proteins and used for filtration and clarification of biological fluids.

New Product

Supplier: I.W. TREMONT CO., INC.

Description: LabExact® HydroBlokr™ is a novel filter technology which reduces serological pipette controller sample cross contamination and device failure with a check-valve effect when wet and blocks further passage of over aspirated aqueous solutions.

New Product

Supplier: I.W. TREMONT CO., INC.

Description: LabExact® Grade C Fine porosity, fast flow rate, with a 1.2 µm size particle retention. Primarily used for RIA procedures and harvesting lymphocytes. Commonly used in environmental test procedures in air and water testing.

New Product

Supplier: I.W. TREMONT CO., INC.

Description: LabExact® disposable non-sterile PVDF hydrophobic filtration media syringe filters feature stability and hydrophobic interactions similar to PTFE with a 1 µm glass microfiber prefilter that raises absorption capacity and loading.

New Product